Post place and route design-technology co-optimization for scaling at single-digit nodes with constant ground rules

Luca Mattii; Dragomir Milojevic; Peter Debacker; Mladen Berekovic; Syed Muhammad Yasser Sherazi; Bharani Chava; Marie Garcia Bardon; Pieter Schuddinck; Dimitrios Rodopoulos; Rogier Baert; Vassilios Gerousis; Julien Ryckaert; Praveen Raghavan

doi:10.1117/1.JMM.17.1.013503

18 January 2018 Post place and route design-technology co-optimization for scaling at single-digit nodes with constant ground rules

Luca Mattii, Dragomir Milojevic, Peter Debacker, Mladen Berekovic, Syed Muhammad Yasser Sherazi, Bharani Chava, Marie Garcia Bardon, Pieter Schuddinck, Dimitrios Rodopoulos, Rogier Baert, Vassilios Gerousis, Julien Ryckaert, Praveen Raghavan

Author Affiliations +

Journal of Micro/Nanolithography, MEMS, and MOEMS, Vol. 17, Issue 1, 013503 (January 2018). https://doi.org/10.1117/1.JMM.17.1.013503

Abstract

Standard-cell design, technology choices, and place and route (P&R) efficiency are deeply interrelated in CMOS technology nodes below 10 nm, where lower number of tracks cells and higher pin densities pose increasingly challenging problems to the router in terms of congestion and pin accessibility. To evaluate and downselect the best solutions, a holistic design-technology co-optimization approach leveraging state-of-the-art P&R tools is thus necessary. We adopt such an approach using the imec N7 technology platform, with contacted poly pitch of 42 nm and tightest metal pitch of 32 nm, by comparing post P&R area of an IP block for different standard cell configurations, technology options, and cell height. Keeping the technology node and the set of ground rules unchanged, we demonstrate that a careful combination of these solutions can enable area gains of up to 50%, comparable with the area benefits of migrating to another node. We further demonstrate that these area benefits can be achieved at isoperformance with >20% reduced power. As at the end of the CMOS roadmap, conventional scaling enacted through pitch reduction is made more and more challenging by constraints imposed by lithography limits, material resistivity, manufacturability, and ultimately wafer cost, the approach shown herein offers a valid, attractive, and low-cost alternative.

Citation Download Citation

Luca Mattii, Dragomir Milojevic, Peter Debacker, Mladen Berekovic, Syed Muhammad Yasser Sherazi, Bharani Chava, Marie Garcia Bardon, Pieter Schuddinck, Dimitrios Rodopoulos, Rogier Baert, Vassilios Gerousis, Julien Ryckaert, and Praveen Raghavan "Post place and route design-technology co-optimization for scaling at single-digit nodes with constant ground rules," Journal of Micro/Nanolithography, MEMS, and MOEMS 17(1), 013503 (18 January 2018). https://doi.org/10.1117/1.JMM.17.1.013503

Received: 16 September 2017; Accepted: 26 December 2017; Published: 18 January 2018

ACCESS THE FULL ARTICLE

INSTITUTIONAL
Select your institution to access the SPIE Digital Library.

SELECT YOUR INSTITUTION

PERSONAL
Sign in with your SPIE account to access your personal subscriptions or to use specific features such as save to my library, sign up for alerts, save searches, etc.

PERSONAL SIGN IN

No SPIE Account? Create one

;

PURCHASE THIS CONTENT

SUBSCRIBE TO DIGITAL LIBRARY

50 downloads per 1-year subscription

Members: $195

Non-members: $335 ADD TO CART

25 downloads per 1 - year subscription

Members: $145

Non-members: $250 ADD TO CART

PURCHASE SINGLE ARTICLE