Neutron radiography and computed tomography may be used to investigate internal structures of complex multi-material objects nondestructively. Thermal neutrons are more effective at producing high-contrast radiographs of objects composed of elements with relatively low atomic numbers (Z). A capability to produce high-quality CT reconstructions from both thermal and fast neutron computed tomography (nCT) using a lens-coupled imaging was demonstrated using various Additively Manufactured (AM’d) and Electrical Discharge Machining (EDM) phantoms, with layers and distinct features, made with intentional voids and out of high- and low-Z elements.
Material identification is challenging for X-ray Computed Tomography (CT) when objects of interest composed of low atomic number (Z) elements are shielded by dense materials. Fast neutron CT (FNCT) can compensate for this shortcoming by providing both penetration through high-Z materials and good contrast in low-Z materials. Here we investigate improvements in X-ray CT feature identification using information from fast neutron imaging. To demonstrate the complementarity of X-ray and FNCT, simulated CT data sets were generated for two heterogenous, nested, cylindrical phantoms using the Monte Carlo N-particle (MCNP) transport code for both imaging modalities. Xray radiographs were simulated for polychromatic 300 keV and 9 MeV e-Bremsstrahlung X-ray sources, while a generic Gaussian D-T source spectrum [En(pk) = 14.10 MeV, w/ FWHM ~ 0.75 MeV] was used for the neutron radiographs. A total of 360 projections taken at 1° intervals were simulated for both modalities and phantoms. All projection data were reconstructed with filtered-back projection (FBP) using the Livermore Tomography Tools (LTT) code. Our results indicate improved material discrimination and resolution of certain features with combined X-ray and neutron CT data sets.
Fast neutron Computed Tomography (nCT) is a powerful and non-invasive imaging modality that can be used to examine features and defects within low Z elements (such as plastic) hidden or shielded by high Z elements (such as tungsten, lead, or even stainless steel). This study built a fast neutron radiography and nCT system and explored various multi-material complex objects utilizing a fast neutron beam at The Ohio State University Research Reactor (OSURR), which provides ~5.4 x 10^7 n·cm-2·s-1 neutron flux at 1.6 MeV (median energy). The lens-based system includes an Electron Multiplying (EM) CCD camera, a light-tight enclosure, and a high light yield 1 cm thick Polyvinyl Toluene (PVT) scintillator provided by Lawrence Livermore National Laboratory (LLNL). A variety of test exemplars were scanned, with the number of projections for each scan ranging from 90 to 180, covering either 180 or 360 degrees. The exposure time for each projection ranged down to one minute, enabling a full nCT scan within a few hours of operation at a 500-kW low power research reactor. 3D tomograms were constructed using Octopus reconstruction software. Results showed that not only could nCT projection data be successfully constructed into volume data, but good contrast between HDPE and a millimeter-sized tungsten ball could be obtained. The 3D tomography presents high contrast to clearly discern HDPE features and voids inside tungsten shielding that are not discernable using 2D radiography.
Lens-coupled X-ray computed tomography (X-ray CT) using a transparent scintillator imaged on a CCD camera obtains higher spatial resolution than the more commonly employed phosphor-enhanced amorphous silicon (A-Si) panels. A-Si panels are limited to resolution typically greater than ~200 microns, have a limited working life due to degradation with dose, and provide intrinsically low efficiency with thin (few hundred microns thick) phosphor coatings. Demanding applications such as imaging the interior of complex additively manufactured components require high throughput and high resolution, best achieved with a lens-coupled system. However, for large fields-of-view, very large area but thin transparent scintillators are required – a format difficult to fabricate with high light yield single crystals – therefore, glass scintillators with both modest X-ray interaction and light yield have been used for years. We have developed a new polycrystalline transparent ceramic scintillator, Gd0.3Lu1.6Eu0.1O3, or “GLO,” that offers excellent stopping power and light yield for improved contrast in sizes up to 14” x 14” plates, with thicknesses in the 2-10 mm range, and we are implementing it in systems to increase imaging throughput for 9 MeV Bremsstrahlung X-ray CT. CT imaging performance will be described.
Fast neutrons accessible from 14-MeV D-T neutron generators have higher transmission through high-Z materials compared to radiography X-rays due to a more uniform attenuation as a function of material Z. These neutrons can therefore image low-Z materials even when shielded by high-Z materials. The constraints in portable fast-neutron digital imaging systems include limited neutron output, limited light produced by neutron imaging scintillators, and lower resolution images due to large source spot size and required scintillator thickness. In addition, digital panel dark-noise counts can be 100x higher than the image signal, and variations across the panel can also be comparable to this signal. We will discuss recent efforts to develop a portable neutron-radiography system, including improved neutron scintillator, mitigation of digital panel noise, and new portable D-T neutron generators. We will also present MCNP efforts to model the system, including neutron scattering effects.
High energy X-rays and neutrons can provide 3-D volumetric views of large objects made of multiple materials. Lenscoupled computed tomography using a scintillator imaged on a CCD camera obtains high spatial resolution, while a surface-mounted segmented scintillator on an amorphous silicon (A-Si) array can provide high throughput. For MeV Xray CT, a new polycrystalline transparent ceramic scintillator referred to as “GLO” offers excellent stopping power and light yield for improved contrast in sizes up to a 12” field-of-view. For MeV neutron CT, we have fabricated both contiguous and segmented plates of “Hi-LY” plastic scintillator, offering light yields 3x higher than standard plastic.
Access to the requested content is limited to institutions that have purchased or subscribe to SPIE eBooks.
You are receiving this notice because your organization may not have SPIE eBooks access.*
*Shibboleth/Open Athens users─please
sign in
to access your institution's subscriptions.
To obtain this item, you may purchase the complete book in print or electronic format on
SPIE.org.
INSTITUTIONAL Select your institution to access the SPIE Digital Library.
PERSONAL Sign in with your SPIE account to access your personal subscriptions or to use specific features such as save to my library, sign up for alerts, save searches, etc.